Re: [opensuse-arm] oS 13.2 on cubieboard1 doesn't start booting
El 2015-03-25 11:03, Volker Kuhlmann escribió: ifconfig -a shows lo (with IP) and eth0 (without IP). # ip a -bash: ip: command not found Perhaps this is the problem, I thought distros went from...
View ArticleRe: [opensuse-arm] oS 13.2 on cubieboard1 doesn't start booting
Does it find the network interface? Log in using the serial console and type "ip a". ifconfig -a shows lo (with IP) and eth0 (without IP). # ip a -bash: ip: command not found Ah, use ifconfig -a then....
View ArticleRe: [opensuse-arm] oS 13.2 on cubieboard1 doesn't start booting
Does it find the network interface? Log in using the serial console and type "ip a". ifconfig -a shows lo (with IP) and eth0 (without IP). # ip a -bash: ip: command not found Perhaps this is the...
View Article[opensuse-arm] Cubieboard monitor output not activated after power-on
openSUSE-Factory-ARM-JeOS-cubieboard.armv7l-1.12.1-Build269.1.raw.xz The DPMI output is not activated when a VGA monitor is connected with a DPMI/VGA adapter and the cubieboard is powered up. Guessing,...
View Article[opensuse-arm] Yast problems
I prefer to use yast-x11 on the cubieboard, it takes a looong time to start but then runs OK (over ssh). There are 2 problems with it: 1) The software management shows 37 autoinstall packages,...
View ArticleRe: [opensuse-arm] kernel update breaks rasperry pi 1
Same with recent openSUSE-Factory-ARM-JeOS-raspberrypi.armv6l-1.12.1-Build289.1.raw.xz Do we have to give up using openSUSE on rasperry pi? Ciao, Michael.
View Article[opensuse-arm] Re: BeagleBone A6 (AKA BeagleBone White) does not boot.
26.03.2015 00:30, Robin Holt пишет: I've just checked 33.4 image with my BeagleBone BLACK, and found it working. As far as I remember BeagleBone White has 256MB RAM. Am I correct? If so, you probably...
View ArticleRe: [opensuse-arm] NTP service fails to start
It's probably not as straightforward, hence my post. It's not in any package in factory: # zypper in logger Loading repository data... Reading installed packages... 'logger' not found in package...
View ArticleRe: [opensuse-arm] oS 13.2 on cubieboard1 doesn't start booting
Oh, ok. All is well then I guess? Well, *networking*, yes. Sorry about the noise there, I don't get it. All depends on if I want it to boot, I guess... ;-) After a day of running it I'm not sure...
View ArticleRe: [opensuse-arm] NTP service fails to start
The file-lists are published for each release, then you can use e.g. https://github.com/benthaman/zyp-file to search them. Regards, Miklos
View ArticleRe: [opensuse-arm] NTP service fails to start
It's probably not as straightforward, hence my post. It's not in any package in factory: # zypper in logger Loading repository data... Reading installed packages... 'logger' not found in package...
View ArticleRe: [opensuse-arm] NTP service fails to start
Ouch. It probably got moved into another package and nobody updated the JeOS package list to include it. logger is in util-linux-systemd.
View ArticleRe: [opensuse-arm] NTP service fails to start
Ouch. It probably got moved into another package and nobody updated the JeOS package list to include it. Please find out which package it is, so we can add it to the list. Or poke the maintainer of...
View Article[opensuse-arm] Moving rootfs to SATA
Instructions for moving the rootfs from uSD card to SATA disk, because I couldn't find it anywhere: Connect SATA disk. An old 2.5" should do, a 3.5" should work too as long as it's powered from...
View Article[opensuse-arm] NTP service fails to start
The NTP daemon doesn't start journalctl -xn shows: Mar 26 15:13:45 linux start-ntpd[1779]: /usr/sbin/start-ntpd: line 144: logger: command not found Mar 26 15:13:45 linux systemd[1]: Failed to start...
View ArticleRe: [opensuse-arm] Cubieboard monitor output not activated after power-on
Sorry I meant HDMI in my previous post, not DPMI. Connecting a DVI monitor with a HDMI-DVI cable to the cubieboard gets the HDMI output activated as expected. With an HDMI/VGA adapter the monitor stays...
View ArticleRe: [opensuse-arm] NTP service fails to start
Hi Volker, Cool! Thanks for finding this out. I've fixed Factory and 13.2 to include this package now, so fixed images should be available shortly. Greetings, Dirk
View ArticleRe: [opensuse-arm] NTP service fails to start
Am 27.03.2015 um 03:35 schrieb Volker Kuhlmann: Well I have to laugh: # cnf -bash: cnf: command not found And cry: # zypper in cnf 'cnf' not found in package names. Trying capabilities. No provider of...
View ArticleRe: [opensuse-arm] NTP service fails to start
Well I have to laugh: # cnf -bash: cnf: command not found And cry: # zypper in cnf 'cnf' not found in package names. Trying capabilities. No provider of 'cnf' found. try "zypper in command-not-found"...
View ArticleRe: [opensuse-arm] Yast problems
Reading through this, maybe you want to start off with an image that already provides all the gfx that you need? We have XFCE, E17 and LXQT images available for pretty much any board that come with a...
View Article