Re: [opensuse-arm] Odroid-C2
Odroid-C2 - boots OK (add fixed, gpio-regulator modules to dracut) [...] Short answer: None, I have not created a JeOS image yet. Just today was U-Boot v2017.05-rc2 packaged, and it'll take a while...
View Article[opensuse-arm] Odroid-C2 (was: Kernel 4.11-rc6 testing status)
Hi Sid, Am 18.04.2017 um 21:35 schrieb Sid Boyce: Odroid-C2 - boots OK (add fixed, gpio-regulator modules to dracut) [...] Short answer: None, I have not created a JeOS image yet. Just today was U-Boot...
View ArticleRe: [opensuse-arm] Kernel 4.11-rc6 testing status
Odroid-C2 - boots OK (add fixed, gpio-regulator modules to dracut) Vega S95 Telos - boots OK (cf. Odroid-C2) [...] NanoPi NEO - boots OK (still no built-in network) UDOO Neo - still hanging No...
View ArticleRe: [opensuse-arm] nanopi neo air ?
Am 27.02.2017 um 14:23 schrieb Andreas Färber: Have you looked at my JeOS-nanopineo? Should be fairly similar. I'll try that - it can't be too difficult to add in a wlan interface. Just to be clear,...
View ArticleRe: [opensuse-arm] Odroid-C2
Odroid-C2 - boots OK (add fixed, gpio-regulator modules to dracut) [...] JeOS-odroidc2 is now bootable - available from Contrib:OdroidC2, instructions at https://en.opensuse.org/HCL:OdroidC2. Burned...
View ArticleRe: [opensuse-arm] Drivers for display for rpi3
Looking at kernel.opensuse.org, kernel-source.git master branch has CONFIG_FB_TFT=m set in config/arm64/default, and so does stable branch. So before we discuss making changes to Leap releases, please...
View ArticleRe: [opensuse-arm] Drivers for display for rpi3
Hi Eric, Am 24.04.2017 um 12:49 schrieb Eric Curtin: Looking at kernel.opensuse.org, kernel-source.git master branch has CONFIG_FB_TFT=m set in config/arm64/default, and so does stable branch. So...
View Article[opensuse-arm] Drivers for display for rpi3
Hi Guys, I recently bought a display that depends on the following driver: https://kernel.googlesource.com/pub/scm/linux/kernel/git/gregkh/staging/+/master/drivers/staging/fbtft/ Could I get these...
View ArticleRe: [opensuse-arm] DT overlays (was: Drivers for display for rpi3)
Look at the ArPi600 link in that category, for instance. For Chistera Pi and TLV493D there are overlay files too, but no links in the Wiki yet. The Arduino Shield, MikroBus and XBee categories should...
View ArticleRe: [opensuse-arm] DT overlays (was: Drivers for display for rpi3)
Look at the ArPi600 link in that category, for instance. For Chistera Pi and TLV493D there are overlay files too, but no links in the Wiki yet. The Arduino Shield, MikroBus and XBee categories should...
View Article[opensuse-arm] DT overlays (was: Drivers for display for rpi3)
Hi Tony, Am 24.04.2017 um 19:19 schrieb Tony Su: Look at the ArPi600 link in that category, for instance. For Chistera Pi and TLV493D there are overlay files too, but no links in the Wiki yet. The...
View ArticleRe: [opensuse-arm] Drivers for display for rpi3
Hi, Am 24.04.2017 um 17:55 schrieb Michal Suchánek: Looking at kernel.opensuse.org, kernel-source.git master branch has CONFIG_FB_TFT=m set in config/arm64/default, and so does stable branch. So before...
View ArticleRe: [opensuse-arm] DT overlays
Am 24.04.2017 um 19:43 schrieb Tony Su: Reminder: Please don't top-post on our mailing lists; reply below. openSUSE uses U-Boot, and U-Boot does not get its Device Tree from the Raspberry Pi firmware,...
View ArticleRe: [opensuse-arm] Odroid-C2
Burned openSUSE-Tumbleweed-ARM-JeOS-odroidc2.aarch64-2017.04.21-Build3.1.raw.xz per instructions, does not boot. Only the red LED lights. It does here. Are you maybe looking at an HDMI screen instead...
View ArticleRe: [opensuse-arm] DT overlays
Thx for looking at this, and your analysis. AFAIK based on existing systemd functionality, I'm not sure that it's quite ready to extend hardware device support, my impression is that although on the...
View Article[opensuse-arm] Firefly RK3399 board
Has anyone had a chance to try this board? With 4GB of RAM on it and a couple of SSDs, it might make a pretty good server/build server/desktop/media center or something....
View ArticleRe: [opensuse-arm] DT overlays
Hi, Am 27.04.2017 um 02:52 schrieb Tony Su: I think you misunderstood: systemd is a way to execute userspace commands on boot, as successor to, e.g., /etc/init.d/boot.local script. It is rumored to be...
View ArticleRe: [opensuse-arm] DT overlays
I think you misunderstood: systemd is a way to execute userspace commands on boot, as successor to, e.g., /etc/init.d/boot.local script. It is rumored to be possible to apply .dtbo files to...
View ArticleRe: [opensuse-arm] Odroid-C2
Did you detach the eMMC for SD testing? I don't have an eMMC module. If you're feeling like experimenting, you could back up your Ubuntu and try dd'ing the JeOS to eMMC. I'm not aware of any special...
View ArticleRe: [opensuse-arm] nanopi neo air ?
Hi Per, Am 18.04.2017 um 18:51 schrieb Andreas Färber: Haven't heard back here yet. Note that I've recently (when touching it) prepared a JeOS image with the above bootloader:...
View Article